Dent puller
With the puller grips a vacuum is created to clamp the suction cup. Can be used for body work,
for example to pull small dents from door panels or fenders. Can also be used to disassemble or mount a small
window, or to hold a car window in place while the sealer is drying.
Use for larger windows suction cup puller |
|
Dent puller
With the locking handles on the suction cups a vacuum is created to clamp the suction cups.
Handy for body work, for example to pull small dents from door panels or fenders. Can also be used
to disassemble or mount larger or slightly bent windows, or to hold a car window in place
while the sealer is drying. Capacity 80 kilo. Take care not to leave window sealant on suction cups.
That diminishes the capacity.
|
|
Flywheel puller
Forged steel puller and hardened steel bolts with metric and inch thread for
British Leyland old Mini series 1 - 2 - 3, 1,1 and series 1 - 2 and 1,3 and
old Mini Metro 1,1 and 1,3 L, HLE, City, S, HLS and old Allegro 1,1 and 1,3.
For transversely mounted A-series engines with Diaphram diaphragm and
upside down mounted Verto clutch units.
|
|
Harmonic balancer puller
For flywheel pulleys, camshaft pulleys, crankshaft vibration dampers and gear pulleys.
This multi functional puller enables alignment pulling with 2 bolts or triangular pulling with 3 bolts.
The flange is equipped with bolt slots. Bolt sizes: 3/8 x 16, 3/8 x 24, 5/16 x 18, M8 x 1,25.
|
|
Pilot bearing puller
For Opel Kadett D and E. Length 460 mm.
|
|
Press and pull set
Universal for sleeves with outer diameter 44 - 82 mm.
To extract and mount ball bearings, bearing bushes,
hydraulic bearings, rubber bearings, silent bearings, shaft seals, etc.
With 8 sleeves, 2 spindles, 4 discs.
|
|
Sheet metal pullers (2)
Set with 2 pullers. Made in USA from very high alloy steel. Specially shaped hook,
takes care of pulling on full material, about 10 mm from the drilled hole. Never pry,
that will causes breakage as the pull will be too much. Maximum pull 225 kilo. Length 155 mm.
|
|
Slide hammer
For pulling dents out of body panels. Make a hole in the dent with an awl,
screw the metal screw in the hole and pull the dent out sliding the hammer.
Slide hammer screw thread connection 1/2 x 13 UNC.
This multi functional puller comes complete with:
1 x |
|
Slide hammer and drive shaft puller
Multi functional puller can be used as heavy duty slide hammer
for internal and external pulling with 2 or 3 hooks and
as drive shaft puller with 2 yokes.
This attractive puller set comes complete with: 3 hook sets, 2 yokes,
screw spindle, puller hook and sheet metal screw in sturdy plastic case.
|
|
Stud extractor set
For removal of studs from the cylinder block. Three internal shafts grip the stud
while turning the stud extractor. Sizes: 6 - 8 - 10 - 12 mm.
Diameter of sizes 6 and 8 mm is 23,6 mm. Length 60 mm. Diameter of sizes 10 and 12 mm is 27,7 mm.
Length 70 mm.
|
|
Stud extractor
For removal of studs from the cylinder block. The black excentric knurled wheel grips
the stud when the part with the square drive is turned. Capacity: 6,5 - 19 mm and 1/4 - 3/4.
Diameter of the bores: 12 mm and 19,5 mm. Drive: 1/2. Diameter of the stud extractor itself: 54 mm.
|
|
Wiper arm puller
For removal of wiper arms that are fitted on spline tapered spigots.
With screw thread and hook feet. Sized for difficult access without damage to the wiper arm.
Can be used for many car makes. Always oil the spindle before use.
Almost universal: for Audi, Fiat, Ford, Honda, Mazda, Mercedes, Mitsubishi, Nissan,
Opel, Peugeot, Porsche, Renault, Rover, Seat, Skoda, Subaru, Toyota, Volkswagen, Volvo.
|
|
Click here | Ball joint separatorsball joint separators |
Midlock Speciaalgereedschap Pauwelussen B.V.
Middelmoot 16, 1721 CZ Broek op Langedijk, Netherlands
Phone: +31 331933 - Mail:
- Internet: www.midlock.nl